| Initial Configuration of device by USB memory |
 |
The device can be configured by using USB memory
Please read the below operational procedure, operating suggestions and conditions for the proper usage. If you agree these terms and conditions, press the file name in the list. Beware that if you executed download,it would be considered that you have agreed to the terms and conditions.
|
|
| 1.Operating procedures |
|
|
.gif) |
|
| 1. |
Decompress file
Download the file and decompress it. |
| 2. |
Insert USB memory into your PC |
| 3. |
Initial-configuration data is downloaded and the value of each setting can be reviewed.
|
|
| * |
Windows Notepad. can be used to view the configuration file. |
| * |
Other text editors can be used in addition to Notepad. |
| * |
The configuration format is: "configuration item name = configuration value" the name describes each configuration item, and each configuration item must be on its own line. |
| * |
The 1st line must be "silex", in order to distinguish this file from other files. |
| * |
When you perform a configuration by using USB memory, please be sure to set "TCP/IP Protocol =1" to enable the use of TCP/IP. |
|
|
| Configuration Settings Explanation |
| Wireless Related Settings |
| Wireless Mode |
0 : OLD Adhoc 1 : Adhoc 2 : Infra |
| SSID |
Arbitrary SSID name
Example: AP-SSID |
| Channel |
Arbitrary channel numbers
Example: 11 |
| USE WEP |
1 : 128Bit encryption 2 : 64Bit encryption |
| WEP Key |
Arbitrary character sequences (hex code) |
| TCP/IP Related Settings |
| DHCP/BOOTP |
0:Disabled 1:Enabled |
| RARP |
0: Disabled 1: Enabled |
| IP Address |
Example: 192.168.1.1 |
| Subnet Mask |
Example: 255.255.255.0 |
| Default Gateway |
Example: 192.168.1.254 |
|
|
|
|
|
| 4. |
The file must be written into the root directory of the USB memory device.
The name must be "config.txt."
|
|
| * |
When you have two or more SX-2000WG(s), the file name format can be "cfgxxxxxx.txt". You can save time and effort by creating multiple configuration files using notepad and saving them in USB memory.
( xxxxxx is the last 6 digits of product serial number and Ethernet address ) |
| * |
Text editors other than notepad can be used. |
|
| 5. |
Perform PRICOM Configuration
|
|
| 1. |
Power off the product and attach the USB memory, containing the configuration information, to a USB port (USB1-USB4). |
| 2. |
Power on the PRICOM. |
| 3. |
Verify that the power LED (orange) lights up. |
| 4. |
If the configuration succeeds, all lights will go off and then the power LED will re-light. |
| 5. |
Please remove the USB memory and connect a printer by the USB cable. |
|
|
| 2.Cautions when using the product |
|
|
|
|
|
| 3.Conditions to use the product |
|
|
|
|
| * |
All rights in relation to this software and its data are reserved to silex technology, Inc. |
| * |
Correcting or altering partially or all of this software is strictly prohibited. Reverse engineering, reverse assembling (reverse compiling), or create anything derived from it is also strictly prohibited. |
| * |
Please download/install this software within your own responsibility. |
|
|
| 4.Download |
|
|
| If you agree to the above written terms and conditions, press the file name in the list. Downloading of the file will be executed. |
|
|
|
| |
|
|
| |
|
