Change the
Configuration Using the Web Browser
This
page explains how to change the configuration using the Web browser.
Since the HTTP protocol is loaded on wiDock, advanced
settings
for wiDock can be configured or changed through a Web browser.
Useful functions including remote restart of wiDock and status
monitor are also available.
 |
- If you wish to change the network settings of wiDock but wiDock is not detected in your network environment,
you need to initialize wiDock. For the initial configuration,
please refer to "Configure Network Settings (for Windows
/ for
Macintosh)".
- We recommend a Web browser to show below.
| Microsoft Internet Explorer 5.5 or higher |
| Netscape Navigator
7.1 or higher |
| Firefox
1.5 or higher |
| Safari 1.0.3 or higher |
- The following explanation is an example when using
Internet Explorer in a Windows XP environment.
Display may vary depending on the Web browser.
- Please use the AC adapter bundled with wiDock.
Other AC adapters may cause unexpected damages.
- If wiDock has been used in another network,
reset it to the factory default settings before you start the
configuration. (Please refer to "Reset
to Factory Default " for details.)
- If enabling the Windows XP embedded firewall function
or using a firewall function of commercial security software, disable
the firewall function while configuring wiDock. Refer to our
support FAQ page on our WEB site at (
http://www.silex.jp/ ) for details.
|
1.Display the Web page of wiDock
2.Configure from the Web page of wiDock
3.Control from the Web page of wiDock
Open the Web page to configure wiDock.
Enter the host name of wiDock into the address bar of the web
browser and click Go.
 |
- The host name of wiDock is a string of SX
plus the serial number of wiDock. If the serial number is
"001122", the host name will be SX001122.
The serial number is the last 6 digits of the Ethernet address which
can be found on the bottom of wiDock. Please refer to the "Parts and Function"
for details.
- For Safari on Macintosh, the following is the
procedure to display the web page of wiDock.
- Click Bookmark
 , and
click Bonjour (or Rendezvous) in the left pane.
- Double click the host name of wiDock in the
right pane.
|
Example: If the Ethernet address is
00:80:92:00:11:22
Enter SX001122. ( It will be displayed as http://sx001122/ )
| Status |
Information of the iPod connected to wiDock and
the status (mode) and operation status of wiDock can be viewed. |
| Easy Configuration |
Configure wiDock in 3 steps. |
| Detailed Configuration |
Configure the detailed network setting of wiDock. |
| System
Information |
Displays
system information and log. Reset to factory default and
restart is available. |
Click the item you wish to configure from the configuration
items displayed in the Web browser.
A configuration screen will be displayed in the Web browser.
|
- Before configuring wiDock, user name and
password are required. When the screen below is displayed, type a user
name (root) and password, then click OK.
( No password is configured on factory default settings. )
|
Click the Easy Configuration
tab. Start the configuration in the order of
"TCP/IP" - "Wireless" - "User Setting". Enter the
value to each configuration item and click Next. When
you finish entering
the "User Setting" values, click Submit.
|
- If the wireless network that you wish to use is not
shown in the list, click Detailed
Configuration and configure each setting.
|
Click the Detailed Configuration
tab. Click
the item you wish to configure. Select or enter a value for the
appropriate item, then click Submit.
| <<
Network Settings >> |
 |
|
| <<
Security >> |
 |
|
| <<
Wireless >> |
 |
|
| <<
User Settings >> |
 |
Click the System
Information tab. You can view the system information,
change the password, reset, check the system log information and update the
firmware.
| <<
System Information >> |
 |
|
| <<
Password >> |
 |
|
| << Reset >> |
 |
|
| <<
Log >> |
 |
|
| <<
Update >> |
 |
Click System Information - Reset.
Click Start for either Reboot or Reset to Factory Default.
